Internet Archive BookReader Heathkit SA 2060 A Deluxe Antenna Tuner (+ Parts + Schem.) (manual). View and Download Heath Heathkit SA-2060A manual online. Deluxe Antenna Tuner. Heathkit SA-2060A tuner pdf manual download. Search for another manual: Manufacturer: Heathkit: Model: SA-2060: Description: Tuner: Type: Complete Manual. Heathkit SA 2060 A Deluxe Antenna Tuner (+ Parts + Schem.) (manual) Item Preview remove-circle Share or Embed This Item.
HEATHKIT. MANUAL for the. DELUXE. ANTENNA TUNER. Model SAA You must deliver the unit at your expense to the Heath factory, any Heathkit. View and Download Heath Kit SAA manual online. Heathkit SAA TV Antenna pdf manual download. Antenna Tuner SA Amateur-D Heathkit Brand, Heath Co.; Benton Harbor Select picture or schematic to display from thumbnails on the right and click for.
Author: | Arajin Faetaxe |
Country: | Hungary |
Language: | English (Spanish) |
Genre: | Education |
Published (Last): | 23 December 2011 |
Pages: | 336 |
PDF File Size: | 8.76 Mb |
ePub File Size: | 15.80 Mb |
ISBN: | 981-1-89847-959-5 |
Downloads: | 40937 |
Price: | Free* [*Free Regsitration Required] |
Uploader: | Mazuk |
Turn one of these nuts onto each threaded rod until it is all the way onto the threaded portion of the rod. They are usually identified by a color code and four or five color bands, where each color represents a number. Do not cut this end off.
HEATH KIT SAA MANUAL Pdf Download.
Tightly twist together the wire ends of the yeathkit sor cable a tightly-wrapped piece of tape may be helpful. Make sure you pull the wires snug for each turn you wind.
Advance the exciter's carrier level power out- put for full power output. Refer to Pictorial Illustration Booklet, Page 5 for the following steps. Refer to Manula D and loosely install a short shaft bushing in the front panel at S.
Connect the end of the black wire to solder lug K NS. Be careful not to over- tighten the hardware or you could damage the meter. With a single switch you may ss-2060 a dummy load, or any of three permanently-connected antennas, in- cluding a long-wire antenna. Sensor cable connections at switch SW3 all correctly wired and well soldered.
Those routed to J7 will affect only the meter circuits. When you are instructed to cut something to a particular length, use the scales rulers pro- vided at the bottom of the Manual pages. Make sure all hardware is tight, 2. High — watts. In sa-0260 same manner, connect a.
Tighten the coupler setscrew onto the capacitor shaft. Then, working from the center outward in both directions, smooth the hewthkit firmly onto the front panel. Follow the instructions carefully.
Antenna Tuner SA-2060
Then connect the other test lead to one of the wires heathkut end B of the balun. Then loosely secure the foot and the screw to the capacitor bracket and the chassis with a 6 ea-2060 washer, a 6 lock washer, and a nut. Back this nut off until two threads are exposed. Most kits use a separate 'Illustration Booklet' that contains illustrations Pictorials, Details, etc.
Then position matching capacitor C2 into the chassis and its shaft all the way into the shaft coupler.
Then start to wrap the 2 -foot length of tape around the outer circumference of the as- sembly to hold these turns in place. Position the wire ends of the balun assembly as shown. Then, do not move the rotor as-2060 this position during any later steps. Parts that should be returned to the factory will be listed on your packing slip. When sa2060 switch is in the Bypass position, signals are routed through the sensor and directly out of the Tuner, bypassing the tuner load-matching function.
As you slide the stepped coupler to- ward the inductor shaft, slide the gear on the inductor shaft forward until the two gears are equally meshed. Page 30 Heathkit Apply a small amount of grease in the reces- sed area in the end of the setscrew installed in hole AS of the rear capacitor plate.
Do not tighten the nut yet. Position the capacitor as heayhkit. Similarly, mount another ceramic insulator plate to the capacitor rear plate at AU and AX. Tighten the nut snugly. This unit has been mnaual calibrated; any attempt to readjust its controls may void the Warranty. Position the chassis as shown in the Pictorial. This is the type we have supplied with the parts. Do not tighten bushing S. This part of the 'Operation' section includes the procedure for using your Antenna Tuner with vari- ous antenna systems.
Turn the detent shaft fully counterclockwise as viewed from the front panelif this has not already been done. Parts Replacement Retain original parts until you receive replacements. Someone who is not familiar with the unit may notice something consistently overlooked by the kit builder.
This Assembly has been factory tested and aligned. Boito shotgun serial number check. Do not tighten the gear setscrew. Connect heathkif end of the white wire to SW3 lug 1 S-l.
Related Posts (10)
HEATHKIT. MANUAL for the. DELUXE. ANTENNA TUNER. Model SAA You must deliver the unit at your expense to the Heath factory, any Heathkit. View and Download Heath Kit SAA manual online. Heathkit SAA TV Antenna pdf manual download. Antenna Tuner SA Amateur-D Heathkit Brand, Heath Co.; Benton Harbor Select picture or schematic to display from thumbnails on the right and click for.
Author: | Goltigor Dinos |
Country: | Mongolia |
Language: | English (Spanish) |
Genre: | Education |
Published (Last): | 8 August 2008 |
Pages: | 68 |
PDF File Size: | 17.22 Mb |
ePub File Size: | 7.73 Mb |
ISBN: | 648-9-92013-203-9 |
Downloads: | 93438 |
Price: | Free* [*Free Regsitration Required] |
Uploader: | Mosar |
This will make the top edge of the ceramic in- sulator plate flush with the top edge of the capacitor rear plate.
Then, while holding the strap forward, tighten the strap mounting screw at C2 hole AR. A voltage sampled directly from heeathkit transmission line is summed with the voltage at L Hold the leads so they cannot fly toward your eyes. Tighten the screw only finger tight. Mount a capacitor mounting bracket to the rear inductor end plate and the remaining spacers at BM and BN.
You can adjust it to sa-260 out load reactance and trans- form the load impedance to the required ohm transmitter or amplifier output impedance. Connect the hook on the free end of the spiral shield to solder lug K NS. Meter Ranges Forward 2 ranges Low — watts.
Tighten the mounting screws at Hheathkit, F, G, and H. Do not overtighten the hardware. Please do not send parts for testing, unless this is specifi- cally requested by our Consultants.
When you are instructed to mount these plates to a capacitor plate, as in the next step, be sure you position the side with the raised area toward the capacitor plate. The REF meter will indicate sa2060 reflected power on the scale.
Any part that is packed in an individual envelope with heathkif part number on it should be placed back in the envelope after you identify it until all the parts are accounted for. Make sure you wrap the tape so it will overlap part of the tape ends already wrapped around the cores.
With a single switch you may select a dummy load, or any of three permanently-connected antennas, in- cluding a long-wire hheathkit. Output Impedance Wide range. Position the two contactor springs toward the ends of the tension rod.
Heath kit SA-2060A Manual
Repeat steps 4 and 5 until you have 26 rotor plates and 25 large spacers installed on the shaft. Be sure to record the settings of both variable capacitor knobs and the counter so you can preset the controls the next time you use a particular band. Turn the rotors of both matching capacitors to their fully-meshed positions. This is the type we have supplied with the parts. During the tuning procedure, apply only enough RF power from the exciter to get a meaningful reading on REF meter Ml in its most sensitive position.
Refer to Detail A and temporarily remove the outer nut from feedthrough J3. Push the spring down and insert the tab of the spring into hole AP in the capacitor rear plate. Secure the strap at AN with a nut. Then tightly twist the wire ends and add a small amount of solder to hold the fine strands together.
Refer to the inset drawing on the Pictorial and be sure SW rotor is positioned exactly as shown. Page 52 Heathkit Coaxial-Fed Antennae An antenna fed with a coaxial line, such as a beam antenna or a center fed dipoie, can easily be matched with your Antenna Tuner to provide a good match to the transmitter across the entire band.
Tl wn350g driver windows 10. Tp-link Tl-wn350g Wireless V1 now has a special edition for these Windows versions: Windows 7, Windows 7 64 bit, Windows 7 32 bit, Windows 10, Windows 10 64 bit, Windows 10 32 bit, Windows 8,Windows Vista Home Premium 64bit, Windows XP Home Edition, for home desktops and laptops 32bit, Windows Vista Ultimate 64bit, Windows 10 Education 64bit, Windows 10 Team 32bit, Windows 8 Enterprise 32bit, Windows 10 Enterprise 64bit, Windows 7 Ultimate 64bit, Windows 10 Pro 32bit, Windows Vista Starter 32bit, Windows 10 Pro Education 64bit, Windows 10 IoT 64bit.
HEATH KIT SAA MANUAL Pdf Download.
Where differences exist between the basic operation of the two circuits, further details will be supplied. This completes the assembly of the matching capacitor. Secure the detent with a control flat washer and a control nut tighten the hardware. Start one end of the prepared tension rod into hole BD in the front inductor end plate. Position the end of the remaining strap coming from the rear of inductor Ll onto the threaded spacer at AT on capacitor Cl.
Detail B Slide the inductor rearward and line up its mounting holes with those in the chassis, Hold the inductor in place.
Heathkit SA A Deluxe Antenna Tuner (+ Parts + Schem.) (manual)
Set the rear inductor end plate aside temporarily. Switches the output to a dummy load, or to any of three coaxial feediines. Ilivid er safe for kids.
The illustrations in the Manual are called Picto- rials and Details. Use enough solder and heat to assure a good con- nection on all six leads and wires at the solder lug.
Then install the setscrew in hole AS. If you are unable to locate an order form, write us a letter or card including: Keep the 'Illustration Booklet' with the As- sembly Manual. Start the free end of the tension rod into hole BL in the rear inductor end plate. If necessary, after the screw is tight, reform the straps slightly to make sure they are as far as possible from the inductor spacer screws at the upper corners.
Heathkit Sa 2060 Manual
Refer to Detail B and loosen the setscrew in the counter shaft stepped coupler. Turn the screw in until the unslotted end is flush with the other side of the plate. Also include switch positions, connections to other units, operating procedures, voltage readings t and any other infor- mation you think might be helpful.
Be sure the small holes in the strap line up with the corresponding hole in the inductor end plate before you tighten the hardware. Use diagonal cutters or scissors. With a very good load, one with less than 1. Place a flat washer, the male heathoit element, and a fiber washer on the stud.
Antenna Tuner SA-2060
Cut the indicated lug of the terminal strip in half as shown. Connect this ground post to a good earth ground or a hdathkit pipe. Push the stepped coupler all the way onto the shaft of the counter before you tighten the setscrew. Avoid eye injury when you cut off excessive lead lengths.
Detail B Slide the inductor rearward and line up its mounting holes with those in the chassis, Hold the inductor in place.
Heathkit SA A Deluxe Antenna Tuner (+ Parts + Schem.) (manual)
Set the rear inductor end plate aside temporarily. Switches the output to a dummy load, or to any of three coaxial feediines. Ilivid er safe for kids.
The illustrations in the Manual are called Picto- rials and Details. Use enough solder and heat to assure a good con- nection on all six leads and wires at the solder lug.
Then install the setscrew in hole AS. If you are unable to locate an order form, write us a letter or card including: Keep the 'Illustration Booklet' with the As- sembly Manual. Start the free end of the tension rod into hole BL in the rear inductor end plate. If necessary, after the screw is tight, reform the straps slightly to make sure they are as far as possible from the inductor spacer screws at the upper corners.
Heathkit Sa 2060 Manual
Refer to Detail B and loosen the setscrew in the counter shaft stepped coupler. Turn the screw in until the unslotted end is flush with the other side of the plate. Also include switch positions, connections to other units, operating procedures, voltage readings t and any other infor- mation you think might be helpful.
Be sure the small holes in the strap line up with the corresponding hole in the inductor end plate before you tighten the hardware. Use diagonal cutters or scissors. With a very good load, one with less than 1. Place a flat washer, the male heathoit element, and a fiber washer on the stud.
Antenna Tuner SA-2060
Cut the indicated lug of the terminal strip in half as shown. Connect this ground post to a good earth ground or a hdathkit pipe. Push the stepped coupler all the way onto the shaft of the counter before you tighten the setscrew. Avoid eye injury when you cut off excessive lead lengths.